 |
 |
 |
|
KIT includes: 1 Tilt Bar (1476) with CUSTOM CUT & PREDRILLED HOLE (13/64" drill bit) , and 2 end Caps (#1839)
You must specify 2 specs: 1/How many holes
2/Distance between Center of Holes, 2 7/8", or 3.00", or 3 1/8"
* See table below for proposed bar length based on 2 specs above
* Spacing between the last hole & end of rod is: 1/2"
| *Distance between Center of Holes | *Number of Holes | *Total length = distance between 1st & Last hole + 1.0" (half inch from last hole to end of bar x 2) | | 2.875" | 6 | 14 3/8" + 1 = 15 3/8" | | 2.875" | 7 | 16 7/8" + 1 = 17 7/8" | | 2.875" | 8 | 20.00" + 1 = 21.00" | | 2.875" | 9 | 22 7/8" + 1 = 23 7/8" | | 2.875" | 10 | 25 1/4" +1 = 26 1/4" | | 2.875" | 11 | 28 3/4" +1 = 29 3/4" | | 2.875" | 12 | 31 5/8" +1 = 32 5/8" |
| *Distance between Center of Holes | *Number of Holes | *Total length= distance between 1st & last hole + 1.0" (half inch from last hole to end of bar x 2) | | 3.00" | 6 | 15.00" + 1 = 16.00" | | 3.00" | 7 | 18.00" + 1 = 19.00" | | 3.00" | 8 | 21.00" +1 = 22.00" | | 3.00" | 9 | 24.00" +1 = 25.00" | | 3.00" | 10 | 27.00" +1 = 28.00" | | 3.00" | 11 | 30.00" +1 = 31.00" | | 3.00" | 12 | 33.00" +1 = 34.00" |
| *Distance between Center of Holes | *Number of Holes | *Total Length= distance between 1st & last hole + 1.0" (half inch from last hole to end of bar x 2) | | 3.125" | 6 | 15 5/8" + 1 = 16 5/8" | | 3.125" | 7 | 18 3/4" + 1 = 19 3/4" | | 3.125" | 8 | 21 7/8" + 1 = 22 7/8" | | 3.125" | 9 | 25.00 + 1 = 26.00" | | 3.125" | 10 | 28 1/8" +1 = 29 1/8" | | 3.125" | 11 | 31 1/4" + 1 = 32 1/4" | | 3.125" | 12 | 34 3/8" + 1 = 35 3/8" |
- Compact Front Tilt Bar with Hollow Core. Vinyl. Off White
The holes are predrilled with 13/64" drill bit. You can make the holes bigger if needed with a bigger drill bit for easier link insertions. - Commonly used in Vinyl, Polysatin, Hunter Douglas Palm Beach,
- Use with cufflink connectors, part #1760, or #1555, sold separately
Cost is $22.00 for rod up to 9 holes. For additional hole, it's $2.00 per hole to compensate for custom drilling service and extra cost for longer bar shipping.
INSTRUCTIONS:
- Insert Cuff Link connectors into holes of LOUVERS first
- PUSH Cuff Link into holes of TILT BAR.
- Insert Tilt Bar End Caps
Drill bit options: 3/16" (.1875"), 13/64" (.203"), 7/32" (.218")
|
|
|
 |
|
 |
|